Electromagnetic Induction Tomography simple model
Hi, I am trying to make a very simple 2D model where I have 2 coils in which in between is a medium (air). One of these coils will be excited and have a magnetic field in the direction of the second...
View Articlefor NdFeB magnet, which constitutive relation is closer to reality
I'm modeling two NdFeB magnets placed very close to each other in a repulsive manner. I need to compute the repelling force between them. There are two options for the constitutive relation. One is B =...
View ArticleConvergence issue with nano pore electrodeposition model
I am trying to model electrodeposition into a nanopores but am having troubles with convergence. My solution only converges to 1e3 fairly consistently even if I refine the mesh and then it starts to...
View ArticleCFD - Surface roughness
Hey guys I really need your help on this one! I was wondering if any of you could tell me about the default settings of surface roughness's in COMSOL? All I've found about it in the documentation is...
View ArticleWhen I have to use 2d or 3d modeling?
Hi Everybody! I´m Wagner, from Brazil and I have a question, a simple question I think! How I decide if my modeling will be in 2d or in 3d? I have Heat Transfer and AC/DC model and I work calculating...
View ArticleHeat Transfer in Fins- Help needed
I am trying to simulate a heat sink, very similar to the one shown in the tutorials... In spite of building a coarse mesh, the solution does'nt converge even after 2 hours of solving. I have an i5...
View ArticleHow can I define nonlinear electric conductivity ?
Hi, I'm currently working on electrical simulation using AC/DC module. How can I define nonlinear electric conductivity of zinc oxide (ZnO) in subdomain settings?
View ArticleProblems with multicore time calculation
Hello everyone, I am working with the attached file and there is a very unusual behavior with the second study. It is a frequency response study with a parametric sweep: I need to know the frequency...
View ArticleCombination of Fluid Flow and Heat Transfer
Hello everyone, I am a new member of this forum and also a fresh user of COMSOL. I hope I will be able to learn from and discuss problems with all of you. My first enquiry to the forum follows: My...
View ArticleHow to use user defined functions as physics's input? Thanks!
Hello, every one! I am learnging to use COMSOL4.2 and want to add AC signal as my device's input. Just as Eric told me to write an equation as the input....
View ArticleImporting a file from AutoCAD to COMSOL
I have created a 3D building model on AutoCAD and wish to import it to COMSOL for CFD analysis. Can I know the process for importing?
View Articleconvective heat flux magnitude
Hi , I'm computing heat transfer from a rotating hot sphere in a fluid medium. The flow is creeping type. I have issues related to the various COMSOL options for convective, conductive and total heat...
View ArticleBuilding a mesh having in a thin gap in between two beams
I am using the piezoelectric devices interface (pzd). Some layers are linear elastic and other - piezoelectric. The surrounding block is air and I defined it with the electrical material model. I want...
View ArticleLiveLink
Dear sir, Is there a LiveLink extension in COMSOL 3.4 version for importing files from AutoCAD to COMSOL?? Please help me out how to find it in my installation?? Thank You...
View Articlesolvers in 4.3a/4.3 version
Hello I am interested in accesing solver information for ODE/PDE in Comsol. So far I was using the Matlab - COMSOL connection in 3.5 version which was showing a sequence like: fem.sol=femtime(fem, ......
View Article2D Model Problem...
Hi all, I'm working on a model which is a 2D representation of a solid container in a multiphase-flow section. what I'm trying to model is to study the relation between the contact angle and the ratio...
View ArticleProblem: Oil Droplets Seem To Dissolve In Water (Two-Phase Flow, Level Set)
I have a problem with my "Two-Phase Flow, Level Set" simulation in COMSOL 4.2. I am trying to simulate the formation of oil droplets in water by hydrodynamic flow focusing. The water and oil are...
View ArticleSurface Integration with different modes
Hi all, I have calculated the results for the different transverse modes in an optical waveguide using the Mode Analysis solver in the RF module. Now I want to perform a surface integration across one...
View ArticleStructure with 2D and a 1D truss...
Hello all, I am trying to implement this (see attachment). I guess it should be relatively easy, and for sure lots of people know how to do it :). After "spending" quite a lot of time, I decide to...
View ArticleSector symmetry on a 1/5 3D electro motor
Hi All, i have a 3D model that shows only 1/5 of whole motor. It has 3 phase and 5 pool pairs. i'm using rotary machinery modul 3D. if i disabled all continuity BC on the outer slice surface, it...
View Article